Here in the next paragraph you can discover more really good information when it comes to How to Install a Bathtub.
Installing a tub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately difficult project. If the old bathtub is readily available, the job can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the new one. Make sure you have actually certified yourself for the task and also are comfortable attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is much better to take into consideration employing one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This article will certainly aid you set up a brand-new bathtub in your washroom if you have already bought a brand-new bathtub as well as do not require to transform the arrangement of your previous water pipes.
Your tools as well as product list should consist of the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome because of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will come from the pipes. When the supply pipes have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before going on to fit the brand-new faucets, contrast the pipe links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines are in place in between the faucet and the sink. Protect the faucet in position with the producer provided backnut. Once the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the tub till the level reviews level.
To set up faucets, fit the bottom of the furthest flexible tap port to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other faucet.
Switch on the supply of water and inspect all joints as well as new pipework for leakages and tighten them if needed. Load the bathtub as well as additionally inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and also securing around the bath tub must wait till the bathtub has actually been utilized at least when as this will settle it into its final setting.
Planning for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps unit to stop strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a rigid seal, creating the water to permeate the wall surface between the bathroom as well as the tiling, causing complications with dampness as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our article about Installing A Bathtub. Thanks for spending some time to read our blog post. Those who appreciated our blog post kindly be sure to share it. Thanks so much for going through it.
Quick response? Dial!